So, habe endlich mal wieder ein bisschen Zeit gefunden mich mit dem Thema zu befassen.
Bin wie folgt vorgegangen:
Code: Alles auswählen
Inhalt der vorhandenen Verzeichnisse gelöscht,
cd $HOME/tuxbox-cvs
export CVS_RSH=ssh
cvs -d anoncvs@cvs.tuxbox.org:/cvs/tuxbox -z3 co -P .
cd $HOME/tuxbox-cvs/cdk
ln -sfv $HOME/Archive Archive
./autogen.sh
./configure --prefix=$HOME/dbox2 --with-cvsdir=$HOME/tuxbox-cvs --with-checkImage=rename --disable-audioplayer --disable picturviewer --enable-automount --enable-maintainer-mode --enable-flashrules --enable-cdkVcInfo
make flash-neutrino-squashfs-all
Die einizgen, wie soll ich sagen, Komplikationen die es gab waren folgende:
- Der Download von "boost_1_40_0.tar.bz2", "libpng-1.2.40.tar.bz2", "libsigc++-1.2.7.tar.gz" hat mal wieder nicht geklappt. Deshalb habe ich diese Kollegen vor'm "make flash-neutrino-squashfs-all" schonmal nach $HOME/Archive geschoben.
(Die Files selbst habe ich von
http://dietmarw.trale.de/Archive/)
- CheckImage meldete bei der neutrino-squashfs.img2x: "!!! If you flash this image these bytes cause 'no system' !!!". Allerdings meldete es das nicht für die img1x, also habe ich das einfach ignoriert.
Image geflasht, uCodes eingespielt und mal wieder: "Es wurden keine Kanäle gefunden! Führen Sie bitte eine Kanalsuche durch"
und wenn ich eine Kanalsuche durchführen möchte: "Kanalsuche fehlgeschlagen!" (und das nach nichteinmal 2 Sekunden Ô.ó).
Und jetzt kommt das beste.
Ich schlepp die Box in's Nebenzimmer und mache dort einen Bootlog unter den selben Bedingungen (SAT angestöpselt, TV auch)
und auf einmal klappt alles. Die D-Box findet beim ersten Suchlauf alle Sender die es so auf Astra 19,2° gibt
Gibt's doch nicht dacht ich mir. Serielles Kabel gezogen und die Box wieder eingeschaltet. Schon wieder "Kanalsuche fehlgeschlagen" und die Geschichte von wegen keine Kanäle.
Ich habe das ganze Szenario wiederholt und es ist repoduzierbar. Sobald der Bootlog läuft (in diesem Fall D-Box 2 Bootmanager) verhält sich die Box absolut normal.
edit: Mir ist noch etwas aufgefallen. Wenn man unter "Treiber- und Bootoptionen" die "EXPERT! Boot-Konsole" auf "seriell" stellt hört der ganze Spuk auf. Sobald "null" eingestellt ist geht es wieder los.
Kann sich das einer von euch erklären ??
P.S. Anbei der "fehlerlose" Bootlog:
Code: Alles auswählen
will verify ELF image, start= 0x800000, size= 170380
verify sig: 262
Branching to 0x40000
U-Boot 2009.08 (Tuxbox) (Okt 30 2009 - 18:19:11)
CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
env: found console with value null
env: found baudrate with value 9600
env: found dbox_duplex with value 0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
LCD: ready
find_inode failed for name=logo-lcd
load: Failed to find inode
ready - can't find logo in flash
find_inode failed for name=logo-fb
load: Failed to find inode
can't find logo in flash
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 670727 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.6-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 670663 Bytes = 654.9 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.6-dbox2 (osi@tuxbox) (gcc version 3.4.6) #1 Fr 30. Okt 18:1
9:45 CET 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600
dbox_duplex=0
Decrementer Frequency = 247125000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:2b:a6:2b
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (squashfs+lzma)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.14.4 (2009-10-30 18:47:02 CET)
starting pid 8, tty '': '/etc/init.d/rcS'
mount: using /etc/fstab
udhcpc (v1.14.4) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Philips
Model: D-BOX2 (2 flash chips)
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: registering frontend 0:0 (TDA8044H QPSK Demodulator)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 600L found.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_av_core: Starting avia_gt_wdt thread.
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Starting the automounter
starting pid 133, tty '': '/etc/init.d/start'
Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.314 2009/10/22 20:48:22 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[timerd] woke up from timer? false!
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.447 2009/10/12 07:22:55 rhabarber1848 Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0 auto_fec 0
[camd] no card is in slot #2
[camd] no card is in slot #1
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
/var/tuxbox/config/zapit/bouquets.xml: No such file or directory
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (2, Philips D-BOX2)
[controld]: ROUTEVIDEO v1 = 1 a1 = 1 v2 = 1 a2 = 1 v3 = 1 a3 = 1 fblk=1
SET VSW: 0 1
SET VSW: 1 1
SET VSW: 2 1
[CVideo::setVideoFormat] output format: 4:3(LB)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[neutrino] registering as event client
[scan-setup] received 31 sats
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/l
iblcddisplay.so.0)
[neutrino] no file /var/tuxbox/config/init.end was found
[neutrino] initialized everything
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[sectionsd] getUTC: read: Connection timed out
[scan-setup] received 31 sats
[neutrino] TP_scan 0 TP_freq TP_rate TP_fec 1 TP_pol 0 TP_mod 6 TP_diseqc 255
re-starting /bin/sectionsd
[sectionsd] starting '/bin/sectionsd'
$Id: sectionsd.cpp,v 1.314 2009/10/22 20:48:22 seife Exp $
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
[sectionsd] getting configuration from environment, starting paused
GETENVI(auto_scanning) = 0
GETENVL(secondsToCache) = 1209600
GETENVL(oldEventsAre) = 3600
GETENVL(secondsExtendedTextCache) = 21600
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
GETENVI(max_events) = 6000
GETENVI(ntprefresh) = 30
GETENVI(ntpenable) = 0
GETENVS(ntp_system_cmd) = /sbin/rdate -s 130.60.7.42
GETENVS(epg_dir) =
GETENVB(update_eit) = 1
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
GETENVB(bTimeCorrect) = 0
GETENVI(debug) = 0
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 1521
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 0263
[camd] set emm caid 1702 capid 1000
[camd] set emm caid 1702 capid 0263
[camd] set emm caid 1702 capid 0263
[dmx.cpp:read:200] read(fd, buf, n): Connection timed out
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
01:04:26.882 [timeThread] - 30.10.2009 21:32:50, tim: Fri Oct 30 21:32:50 2009
[neutrino] timeset event. difference is 1256934504 s, stepping...
01:04:26.960 [timeThread] Time set via DVB, going to sleep for 1800 seconds.
21:32:50.948 dmxSDT: going to sleep...
/tmp/currentservices.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[timerd] using config file /var/tuxbox/config/timerd.conf
PES, queue 0 normal.
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 16:9)
21:32:55.328 eit_set_update_filter, servicekey = 0x41b00017031, current version
16
Freundlich grüßt der momentan total verwirrte OSi
,d.h. keinerlei Auswirkung wenn kein logo-fb oder logo-lcd vorhanden ist. Wenn Du selbst Images baust kannst Du ja Images ohne vorinstallierte Logos bauen und die starten auch ganz normal.
